Showing results: 376 - 390 of 639 items found.
-
ICS Electronics
All of ICS's Serial Digital Interfaces are user configurable and let you transfer data as bits, bytes or as strings of bytes. All data lines are high power TTL outputs or floating inputs with pullup resistors for sensing CMOS signals or switch contacts. All interfaces conform to the IEEE-488.2 Standard and are HP-IB compatible.
-
Model 2364 OEM -
ICS Electronics
* 114521-11 Board provides 16 low-level form A contacts (SPST).* Provides 8 isolated inputs for CMOS, TTL and 32 Vdc signals.* Multiple relay programming modes switch individual relays or san with single or multi-pole contacts.* Fully IEEE-488.2 and SCPI compliant.* Serial interface header includes RS-232 and RS-485 signals. * GPIB interface header includes GPIB address switch input signals.* Includes 50-pin mating relay connector and serial header connector.* Optional 115750 Terminal Board for easy connections without soldering.* Operates on 12 to 24 Vdc power.* Use an ICS GPIB Connector/Address Switch Assembly to mount a GPIB connector and Address Switch on the rear panel.
-
SAM-3 -
Macintyre Electronic Design Associa
The SAM-3 is a portable single channel signal conditioneer specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from eitherits internal batteries or the power line. It incorporates two sets of power line rejection fileters, switch selectable fro 50 to 60 Hz and the corresponding first four harmonics.
-
Model 4816 -
ICS Electronics
* Provides GPIB-to-serial and RS-232-to-RS-485 conversion path for serial devices with RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Dual GPIB headers support GPIB connections with a GPIB Connector/Address Switch Assembly or with a GPIB Flat Ribbon Cable.
-
Acces I/O Products, Inc.
Relay is the name for a switch that is operated electro-mechanically or electronically. Their main task is to make and break connections to control the flow of current in electrical circuits. They’re used for various purposes ranging from validating semiconductors to interfacing low power computers or microcontrollers with high power machinery.
-
In-Phase Technologies, Inc.
Our standard line of switch matrices includes automated control via our command customizable controller. Interface options include USB, LAN, IEEE-488, and many other options that can customize our standard switch to meet your needs. ur existing designs cover a wide array of topologies, frequencies up to 70Ghz. and power levels from milliwatts through kilowatts.
-
TCM-1A -
Macintyre Electronic Design Associa
The TCM-1 is a three-channel portable signal conditioner specifically tailored to provide power to and process the signals from MEDA's line of AC magnetic field sensors. The unit operates from either its internal batteries or the power line. It incorporates two sets of power line rejection filters, switch selectable for 50 or 60 Hz and the corresponding first four harmonics.
-
SR-112 -
Brainstorm Electronics Inc.
Like it’s big brother the SR-112 Distripalyzer, the SR-28 can drive time code over long cables, making it ideal for synchronization during live shows and remote recording. The SR-28 time code distributor, with two inputs and eight outputs, reshapes time code while distributing it, eliminating amplitude distortions and level fluctuations. The level of each output is individually adjustable via front panel pots. The input is selected via a front panel switch. Also included are 2 power inputs and an automatic switch over in case of failure.
-
SR-28 -
Brainstorm Electronics Inc.
The SR-28 can drive time code over long cables, making it ideal for synchronization during live shows and remote recording. The SR-28 time code distributor, with two inputs and eight outputs, reshapes time code while distributing it, eliminating amplitude distortions and level fluctuations. The level of each output is individually adjustable via front panel pots. The input is selected via a front panel switch. Also included are 2 power inputs and an automatic switch over in case of failure.
-
Mors Smitt Group
A Timer Relay is a combination of an electromechanical output relay and a control circuit. The contacts will open or close before or after a pre-selected, timed interval. Time delay relays are initiated or triggered by one of two methods:*Application of input voltage/auxiliary supply will either initiate the unit or make it ready to initiate when a trigger signal is applied. *Applying a trigger signal is used to initiate the unit after input voltage has been applied. This trigger signal can either be a control switch (dry contact switch) or a power trigger (voltage).
-
Acopian Technical Company
Contacts to control an external horn or light, or to signal your PLC are now available on independent accessories for any power supply. These modules can be used on power supplies with DC voltages from 5 to 125 Vdc. SPDT relay contacts switch if the power supply’s output deviates by:*1.0 volt or more (for 5 volt outputs)*2.0 volts or more (for 6 to 48 volt outputs)*3.0 volts or more (for 49 to 125 volt outputs)
-
xiQ -
XIMEA GmbH
*Ultra compact mini camera- Only 26.4 x 26.4 x 21.2 mm and mere 27grams (1)*Cool - Low power consumption with 1.0 to 1.8 W and minimal heat dissipation*Fastest - High speed, high frame rate: 500fps at VGA and 90fps at 4Mpix resolutions*AIA standard - USB3 Vision standard compliant*Supported - USB3 under Windows 7 and 10, macOS, Linux, ARM and various Machine Vision Libraries*Industry standard interface - Compatible with USB 3.1 Gen1 SuperSpeed specification*Powerful potential - 5 Gbit/s interface 400 MB/s data throughput*Connectivity and Synchronization - Programmable opto-isolated input and output, 3 status LEDs*Cost efficient - Excellent value for the price, low TCO and fast ROI*Software interfaces - GenICam / GenTL and highly optimized API / SDK for Image Processing*Easy deployment - Range of accessories and widest hardware and software interoperability*Time proven - In production since the end of 2011*User friendly - Intuitive and simple to use API, easy switch from C to CS mount and more*Highly Customizable - Available in Board level (single PCB) and with different connector types
-
NI
The Voltage Input Device for FieldDAQ measures up to eight ±10 V channels with 24-bit resolution and simultaneous sample rates up to 100 kS/s/ch. Some models can power sensors, such as pressure sensors, with up to 24 V per input channel. This device offers 500 V channel-to-channel isolation, protecting instrumentation from high-transient voltages. Additionally, the device is IP65 and IP67 rated to be dust-proof and water-submersible, can operate in -40 °C to 85 °C environments, and can sustain 100 g shock and 10 g vibration. It has an integrated network switch for simplified daisy chaining and provides tight synchronization over time sensitive networking (TSN) for distributed data acquisition systems.The Voltage Input Device for FieldDAQ includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
115250 -
ICS Electronics
* C-Size blank PC Board for mounting devices, modules or circuits.* Includes VXIbus P1 and P2 connectors and decoupled power pads.* Includes pads for all VXI bus signals.* Includes pad patterns for common front panel connectors, LEDs, and a Reset Switch.* Includes CAD Design aids for Schematic Capture, PC board layout and front panel machining.* Use with ICS 1, 2 and 3-slot wide Module Shield Kits to create a complete enclosed module.* Use with ICS Front Panel Kits to add a front panel and ejectors to the blank board.
-
Comtel Electronics
The Comtel VXS Backplane 21 slots match performance and cost-effectiveness by realising a fully optimised signal and power distribution environment. Design techniques ensure uniform impedance controlled signaling environment and ground guarding minimises line-to-line crosstalkThe VXS provides the high-speed switched serial performance of VITA 41, hybrid design includes VXS payload slots, VXS switch slots and conventional VME64x slots, The 21 slot VXS backplanes supports data rates well beyond 3.125Gb/s per link. As a dual-star design, it can be operated with two switch boards, allowing addressing of both link ports on payload cards.
